SAB 163
Дополнительную информацию по продукции Sabroe Вы можете найти на сайте http://coolref.ru/.
Описание компрессора SAB 163
Компрессор SAB 163 Mk3 - это винтовой компрессор с регулируемой производительностью и системой впрыскивания масла.
Два ротора имеют соответственно 4 зуба (ведущий ротор) и 6 зубьев (ведомый ротор) асимметричного профиля в соответствии с лицензией SRM. На стороне всасывания роторы оснащены роликовыми подшипниками, в то время как подшипники на стороне нагнетания представляют собой комбинированный набор подшипников, состоящий из роликовых подшипников, которые принимают на себя радиальные нагрузки, и шарикоподшипников, воспринимающих осевые нагрузки. Осевые нагрузки частично воспринимаются вращающимися уравновешивающими поршнями, установленными на роторах.
Роторы могут поставляться изготовленными из закаленной или незакаленной стали. Если компрессор оснащен ротором из закаленной стали, то электродвигатель может подсоединяться к ведомому или ведущему ротору. Неиспользуемая шейка вала закрыта крышкой.
В случае ротора из незакаленной стали электродвигатель может подсоединяться только к ведущему ротору.
На шейке вала, к которой подсоединяется электродвигатель, установлено сальниковое уплотнение типа скользящего кольца, которое создает эффективное уплотнение между внутренней полостью компрессора и атмосферой.
В компрессоре имеется большой встроенный всасывающий фильтр, который предотвращает попадание в компрессор загрязнений, поступающих вместе со всасываемым паром из холодильной установки.
Кроме того, компрессор оснащен обратным клапаном, который не допускает обратного вращения роторов вслучае отключения подачи напряжения на электродвигатель. Обратный клапан управляется внутренним давлением всасывания компрессора, при этом он открыт во время работы компрессора, не вызывая чрезмерного падения давления всасываемого пара.
Компрессорный агрегат SAB 163 Mk3 имеет компактную конструкцию со встроенным масляным фильтром и электрическим реле расхода, что сокращает количество соединительных труб.
Производительность компрессора может регулироваться бесступенчато от 10% до 100% с помощью регулирующего золотника, расположенного под роторами. Система золотника приводится в движение поршнем, на который оказывает воздействие давление пара на стороне нагнетания компрессора и давление масла, регулируемое соленоидным клапаном. Обычно управление соленоидным клапаном осуществляет микроэлектронная система управления "Сабро" UNISAB II.
Винтовой компрессор SAB 163 Mk3 имеет также другую систему регулирования, посредством которой можно регулировать встроенное объемное отношение компрессора Vi. Эта система всегда обеспечивает самый высокий кпд компрессора даже при колеблющемся рабочем давлении холодильной установки.
Регулирование Vi, наиболее эффективно, когда компрессор работает на 100% производительности, и действует как механический останов для упомянутого выше золотника производительности. При этом золотник производительности регулирует величину окна, через которое выходит нагнетаемый пар, так что степень сжатия в компрессоре соответствует отношению давлений стороны нагнетания и стороны всасывания в холодильной установке.
При пониженной производительности компрессора система регулирования Vi имеет всего лишь незначительное действие. Встроенное объемное отношение может регулироваться двумя путями:
Встроенное объемное отношение Vi регулируется вручную путем вращения ходового винта, расположенного подшейками валов роторов, в соответствии с графиками, приводимыми в руководстве.
Встроенное объемное отношение Vi регулируется автоматически посредством давления масла и двух соленоидных клапанов, управляемых системой UNISAB II.
Запасные части для компрессора SAB 163
| List of parts for SAB 163 Mk3 | ||||
| Relevant drawing: 06G1-884 | ||||
| Unless otherwise stated all measurements ara givan in mm. | ||||
| Pos. | Designation | Quantity | Part no. | |
| Aut.Vi | Man.Vi | |||
| Complete compressor, female drive, Man.Vi | 1(F) | 4161-069 | ||
| Complete compressor, female drive, Aut. V, | 1(F) | 4161-070 | ||
| Complete compressor, male driva, Man. Vi | 1(M) | 4161-071 | ||
| Complete compressor, male driva, Aut.Vi | 1(M) | 4161-073 | ||
| Compressor housing | ||||
| 10 | Rotor housing, SAB -163H | 1 | 1 | 3011-020 |
| Bearmg cover at suction end | ||||
| 20 | Suction cover for SAB 163 M | 1 | 1 | 3013-141 |
| 21 | O-ring 380.37 x 5.33 | 1 | 1 | 1331-187 |
| 22 | Cylindrical pin dia. 16 x 50 | 2 | 2 | 1445-091 |
| 23 | Cylinder screw M16 x 45 | 16 | 16 | 1413-433 |
| 24 | Plug with collar 1/2" | 1 | 1 | 1343-027 |
| 25 | Aluminium gasket dia. 27/21 x 1,5 | 1 | 1 | 2356-133 |
| Bearing cover at discharge end | ||||
| 40 | Cover for bearings | 1 | 1 | 3013-017 |
| 43 | Cylinder screw M10 x 35 | 6 | 6 | 1413-373 |
| 44 | Adjusting screw M20 | 2 | 2 | 2111-122 |
| 45 | Locking screw M6 x 10 | 4 | 4 | 1413-231 |
| Capacity regulating cylinder | ||||
| 50 | Capacity cylinder | 1 | 1 | 3043-009 |
| 51 | O-rlng 107.54 x 3.53 | 1 | 1 | 1331-085 |
| 52 | Cylinder screw M12 x 40 | 3 | 3 | 1413-358 |
| Cover for capacity regulating cylinder | ||||
| 60 | Cover for capacity cylinder | 1 | 1 | 3013-194 |
| 61 | O-ring 120.24 x 3.53 | 1 | 1 | 1331-089 |
| 62 | Cylinder screw M12 x 30 | 4 | 4 | 1413-386 |
| Housing for capacity indicator | ||||
| 70 | Capacity indicator housing | 1 | 1 | 3045-002 |
| 71 | Cylinder screw M6 x 30 | 4 | 4 | 1413-343 |
| 72 | Capacity indicator cover | 1 | 1 | 3045-003 |
| 73 | Cylinder screw M6 x 50 | 4 | 4 | 1413-347 |
| 74 | O-ring 98.02 x 3.53 | 1 | 1 | 1331-081 |
| 75.1 | Sight glass for capacity indicator | 1 | 1 | 3045-006 |
| Shaft seal cover | ||||
| 80-1 | Shaft seal cover, before jure 1998 | 1 | 1 | 3013-142 |
| 80-2 | Shaft seal cover, before jure 1998 | 1 | 1 | 3013-209 |
| 81 | O-ring 113.89 x 3,53 | 1 | 1 | 1331-087 |
| 82-1 | Cylinder screw M12 x 50, before june 1998 | 1 | 1 | 1413-390 |
| 82-2 | Cylinder screw M12 x 35, before june 1999 | 2 | 2 | 1413-367 |
| 82-3 | Cylrnder screw M12 x 35, after june 1998 | 4 | 4 | 1413-387 |
| 83 | Driving pin dia. 4 x 6 | 1 | 1 | 1446-011 |
| 84 | Plug with rim 1/4" | 1 | 1 | 1343-025 |
| 85 | Gasket dia. 19/14 x 1,5 | 1 | 1 | 2356-124 |
| 86 | Hose connecting branch '1/4" | 1 | 1 | 1345-143 |
| 87 | Clear plastic hose 3/16" x 300 mm | 1 | 1 | 1241-190 |
| 88 | Plug with rim 3/8", before june 1998 | 1 | 1 | 1343-026 |
| 89 | Dowty ring dia 23,8/17,35 x 2, before june 1998 | 1 | 1 | 1331-427 |
| Cap cover | ||||
| 90 | Cap cover | 1 | 1 | 3013-036 |
| 91 | O-ring 113.89 x 3.53 | 1 | 1 | 1331-087 |
| 92 | Cylinder screw M12 x 35 | 3 | 3 | 1413-387 |
| Cover for slide stop | ||||
| 100 | Slide stop cover | 1 | 3013-068 | |
| 101 | O-ring 78,97 x 3.53 | 1 | 1331-076 | |
| 102 | Cylinder screw M12 x 35 | 4 | 1413-387 | |
| 103 | Bearing retainer | 1 | 3021-018 | |
| 104 | Cylinder screw M6 x 20 | 4 | 1413-341 | |
| 105 | Locking plate | 1 | 2114-043 | |
| Rotors and suction end bearings | ||||
| 110 | Rotor set for SAB 163 H, female drive | 1(F) | 1(F) | 3024-006 |
| 110 | Rotor set for SAB 1631H, male drive | 1(M) | 1(M) | 3024-106 |
| 111 | Radial roller bearing | 2 | 2 | 1513-017 |
| 113 | Oil splash ring external dia. 46 | 1 | 1 | 1437-287 |
| 114 | Washer for bearing | 2 | 2 | 3021-007 |
| 115 | Cylinder screw M16 x 45 | 2 | 2 | 1413-433 |
| 118 | Driving pin dia. 4.0 x 10 | 1 | 1 | 1446-012 |
| 119 | Retainer pin | 2 | 2 | 3021-009 |
| 120 | Balance piston, suction end | 1 | 1 | 3025-008 |
| Discharge end bearings, female rotor | ||||
| 130 | Balance piston dia. 86 | 1 | 1 | 3025-037 |
| 131 | Radial roller bearing dia. 55/120 x 43 | 1 | 1 | 1513-017 |
| 132 | Four point bearing dia 55/120 x 29 | 1 | 1 | 1513-029 |
| 133 | Set of shims dia. 100/120, for adjusting the | |||
| clearance between the rotors and outlet ports, | 1 | 1 | 2124-082 | |
| Comprising; 1 off thickness 0.49 mm | ||||
| 1 off - 0.52 mm | ||||
| 1 off - 0.55 mm | ||||
| 1 off - 0.56 mm | ||||
| 1 off - 0.61 mm | ||||
| 1 off - 0.64 mm | ||||
| 1 off - 0.67 mm | ||||
| Discharge end bearings, mate rotor | ||||
| 135 | Balance piston dia. 86 | 1 | 1 | 3025-037 |
| 136 | Radial roller bearing dia.60/130 x 46 | 1 | 1 | 1513-013 |
| 137 | Four point bearing dia.60/130 x 31 | 1 | 1 | 1513-030 |
| 138 | Set of shims dia. 105/130 for adjustnig the. | |||
| clearance between, the rotors and outlet ports, | 1 | 1 | 2124-083 | |
| Comprising 1off thickness 0.49 mm | ||||
| 1 off - 0.52 mm | ||||
| 1 off - 0.55 mm | ||||
| 1 off - 0.58mm | ||||
| 1 off - 0.61 mm | ||||
| 1 off - 0.64 mm | ||||
| 1off - 0.67 mm | ||||
| Discharge end ports | ||||
| 140 | Outlet port (male rotor) | 1 | 1 | 3031-035 |
| 141 | Outlet port (femle rotor) | 1 | 1 | 3031-036 |
| 142 | Cylinder screw M10 x 150 | 6 | 6 | 1413-376 |
| 143 | Steel gasket dia. 16/10 x 2 | 6 | 6 | 2351-030 |
| 144 | Set screw M10 x 20 (first production series) | 2 | 2 | 1413-252 |
| 145 | Set screw M10 x 10 (first production series) | 2 | 2 | 1413-250 |
| 146 | Blank-off screw | 2 | 2 | 1343-026 |
| 147 | Locking screw M 10 x 10 (new productian series) | 2 | 2 | 1413-253 |
| 148 | Adjusting screw M10 x 20 (new productian series) | 2 | 2 | 1413-032 |
| 149 | Gasket | 2 | 2 | 1331-427 |
| Parts for adjusting rotors | ||||
| 151 | Inner cover (male rotor) | 1 | 1 | 3013-019 |
| 152 | O-ring 123.42 x 3.53 | 1 | 1 | 1331-090 |
| 153 | Inner cover (female rotor) | 1 | 1 | 3013-045 |
| 154 | O-ring 113.89 x 3.53 | 1 | 1 | 1331-087 |
| Shaft seal | ||||
| 160 | Shaft seal type 680 | 1 | 1 | 3084-529 |
| Suction filter | ||||
| 170 | Suction filter | 1 | 1 | 3042-081 |
| 171 | Set screw M6x 10 | 3 | 3 | 1413-231 |
| Adjusting system for Vi -slide | ||||
| 180 | Spindle for slide stop | 1 | 3044-012 | |
| 182 | Sealing washer for slide stop | 1 | 3044-014 | |
| 183 | Sealing ring dia 28/22 | 1 | 1331-503 | |
| 184 | O-ring 44.04 x 3.53 | 1 | 1331-065 | |
| 186 | Axial ball bearing dia. 42/25 x 11 | 2 | 1512-015 | |
| Slide stop | ||||
| 190 | Slide stop (included in pos.192 and pos. 370) | |||
| Man. Vi - slide | ||||
| 191 | Spring | 1 | 1 | 1523-162 |
| 192 | Slide control (including slide stop, pos. 190) | 1 | 3044-066 | |
| 193 | Cylinder screw M10 x 12 | 1 | 1 | 1413-408 |
| Capacity regulating slide | ||||
| 200 | Capacity slide | 1 | 1 | 3043-174 |
| 201 | Inner piston slide | 1 | 1 | 3043-092 |
| 202 | Outer piston slide | 1 | 1 | 3043-093 |
| 203 | O-ring 53.57 x 3.53 | 1 | 1 | 1331-068 |
| 204 | Gasket | 1 | 1 | 1332-107 |
| 205 | Cylindrical pin dia. 6 x 12 (included in pos no 207) | (1) | (1) | 1445-075 |
| 206 | Cylinder screw M6 x 25 | 4 | 4 | 1413-342 |
| 207 | Slide rod | 1 | 1 | 3043-111 |
| 208 | Tape bearing | 2 | 2 | 2132-104 |
| 209 | O-ring 21.62 x 3.53 | 1 | 1 | 1331-020 |
| Spindle for capacity regulation | ||||
| 210.1 | Spindle for capacity indicator | 1 | 1 | 3045-058 |
| 216 | Magnetic coupling | 1 | 1 | 3045-061 |
| 217 | O-ring dia 44,12 x 2,62 (incl.in pos.216) | (1) | (1) | 1331-146 |
| 218 | Hexagon head screw M4 x 16 (inci. in pos. 216) | (1) | (1) | 1413-320 |
| 219 | Hexagon head screw M4 x 20 (incl. in pos. 216) | (2) | (2) | 1413-322 |
| Capacity indication | ||||
| 221 | Indicator dial | 1 | 1 | 3045-001 |
| 233 | Cylinder screw M4 x 10 | 1 | 1 | 1413-319 |
| 224 | Supporting ring | 1 | 1 | 2356-155 |
| 226 | Locking washer DC 15/8,4 | 1 | 1 | 1437-054 |
| 227 | Locking washer DC 8/4,3 | 1 | 1 | 1437-060 |
| Suction gas inlet | ||||
| 252 | O-ring dia.190.09 x 3.53 | 1 | 1 | 1331-105 |
| 253 | Inlet flange | 1 | 1 | 3013-130 |
| 254 | Cylinder screw M 16 x 45 | 8 | 8 | 1413-433 |
| 257 | Plug 1/4" | 1 | 1 | 1343-025 |
| 258 | Gaskel ring dia. 21/14 x 2,0 | 1 | 1 | 1331-428 |
| 259 | O-ring dia. 20,22 x 3,53 | 1 | 1 | 1331-019 |
| Non-return valve | ||||
| 260 | Valve cone | 1 | 1 | 3042-107 |
| 261 | Spring | 1 | 1 | 1523-033 |
| 262 | Cylinder screw M10 x 25 | 1 | 1 | 1413-371 |
| 263 | Adaptor | 1 | 1 | 3042-079 |
| 264 | Tape bearing dim 10 x 1 x 136 | 2 | 2 | 2132-125 |
| 265 | Locking device | 1 | 1 | 3042-108 |
| 266 | Pointed screw M6 x 6 | 1 | 1 | 1413-229 |
| Suction side connection | ||||
| 279 | Flange | 1 | 1 | 3013-130 |
| 280 | Cylinder screw M 16 x 45 | 8 | 8 | 1413-433 |
| 281 | O-ring 190.09 x 3.53 | 1 | 1 | 1331-105 |
| Economizer inlet | ||||
| 290 | ECO plug | 1 | 1 | 3013-128 |
| 291 | Cylinder screw M10 x 30 | 1 | 1 | 1413-372 |
| 292 | O-ring 37.69 x 3.53 | 1 | 1 | 1331-030 |
| 293 | Cylinder screw M8 x 25 | 1 | 1 | 1413-357 |
| HLI inlet | ||||
| 300 | HLI plug | 2 | 2 | 3013-127 |
| 301 | Cylinder screw M10 x 30 | 4 | 4 | 1413-372 |
| 302 | O-ring 23.39 x 3,53 | 2 | 2 | 1331-022 |
| Connecting parts for slide rod | ||||
| 310 | Washer for slide rod | 1 | 1 | 3043-109 |
| 310 | Cylinder screw M10 x 65 | 1 | 1 | 1413-383 |
| Internal oil piping | ||||
| 320-1 | Pipe set complete, female drive, before june 1998 | 1 | 1 | 3049-045 |
| 320-2 | Pipe set complete, male drive, before june 1998 | 1 | 1 | 3049-030 |
| 320-3 | Pipe set complete, female drive, after june 1998 | 1 | 1 | 3049-045 |
| 320-4 | Pips set complete, male drive, after june 1998 | 1 | 1 | 3049-046 |
| 325.1 | Orifice dia. 7 for oil injection pipe - R717 | 1 | 1 | 3142-062 |
| 325.2 | Orifice dia. 5 for oil injection pipe - R22 and HFC's | 1 | 1 | 3142-052 |
| 331 | Plug 1/3" | 1 | 1 | 1343-027 |
| 332 | Gasket ring dia. 28,5/21,6 x 2,3 | 1 | 1 | 1331-430 |
| 333 | Plug 1/4" | 1 | 1 | 1343-025 |
| 334 | Gasket ring dia. 21/14 x 2,0 | 1 | 1 | 1331-428 |
| 335 | Plug 1/4" | 1 | 1 | 1343-025 |
| 336 | Gasket ring dia. 21/14 x 2,0 | 1 | 1 | 1331-428 |
| 337 | Plug 3/4" | 1 | 1 | 1343-028 |
| 338 | Gasket ring dia 34,93/27,13 x 2,34 | 1 | 1 | 1331-433 |
| Electrical signal transmitter for | ||||
| capacity slide positon (optional) | ||||
| 350 | Turning transmitter | 1 | 1 | 3448-004 |
| 351.1 | Sight glass for transmitter | 1 | 1 | 3045-007 |
| 352 | Screw for transmitter M3 x 8 (inducted in pos. 350) | 4 | 4 | 1412-012 |
| Limitation of minimum capacity (optional) | ||||
| 228 | Spacer ring for SAB 163H | 1 | 1 | 3045-029 |
| 229 | O-ring dia. 113.89 x 3.53 | 1 | 1 | 1331-087 |
| 210.2 | Spindle | |||
| (replaces pos. 210.1) | 1 | 1 | 3045-064 | |
| 75.2 | Glass for indicator, SAB 128/163 | |||
| (replaces pos. 75.1) | 1 | 1 | 3045-036 | |
| 351.2 | Giass for indicator, SAB 128/163 for turning transmitter | |||
| (replaces pos. 351.1) | 1 | 1 | 3045-037 | |
| Aut. Vi slide | ||||
| 370 | Slide control for auto. Vi | |||
| (including slide stop pos.190) | 1 | 3044-065 | ||
| 371 | Gasket dia. 72 | 1 | 1333-119 | |
| 372 | Piston for Auto. Vi | 1 | 3044-042 | |
| 373 | Cylindrical pin dia. 6 x 12 | |||
| (included in pos. 372) | 1445-075 | |||
| 374 | Cylinder screw M6 x 12 | 4 | 1413-339 | |
| Cover for slide stop | ||||
| 380 | Slide stop cover for auto. Vi | 1 | 3013-195 | |
| 381 | O-ring 78.97 x 3.53 | 1 | 1331-076 | |
| 382 | Cylinder screw M12 x 30 | 4 | 1413-386 | |
| 383 | Cylindrical pin dia 8 x 24 | 1 | 1445-077 | |
| Spindle for V| indication | ||||
| 390 | Spindle for auto. Vi | 1 | 3044-062 | |
| 395 | Driving disc | 1 | 3044-021 | |
| 396 | Cylinder screw M 4x 12 | 1 | 1413-318 | |
| Bearing retainer Tor Aut. Vi | ||||
| 400 | Bearing retainer tor aut. Vi | 1 | 3044-064 | |
| 401 | Cylinder screw M6 x 45 | 4 | 1413-307 | |
| 402 | Cover for the transmitter | 1 | 3045-009 | |
| 403 | Cylinder screw M4 x 10 | 4 | 1413-319 | |
| 405 | Magnetic coupling | 1 | 3045-062 | |
| 406 | O-ring dia. 32,09 x 2,62 (incl. in pos. 405) | (1) | 1331-133 | |
| 407 | Hexagon head screw M4 x 16 (incl. in pos. 405) | (1) | 1413-320 | |
| Electrical signal transmitter for | ||||
| Vi-slide position (optional) | ||||
| 410 | Turning transmitter | 1 | 3448-004 | |
| 411 | Driving lug | 1 | 3044-020 | |
| 413 | Pointed screw M4 x 5 | 1 | 1413-211 | |
| 413 | Clamping pin dia. 1,5 x 12 | 1 | 1446-010 | |
| 415 | Screw for transmitter M3 x 8 (included in pos. 410) | 4 | 1412-012 | |
| Oil filter parts | ||||
| 450 | Cover | 1 | 1 | 3041-008 |
| 452 | O-rmg dia 132,94 x 3,53 | 1 | 1 | 1331-093 |
| 453 | O-ring dia 101,19 x 3,53 | 1 | 1 | 1331-083 |
| 455 | Locking nut M10 | 1 | 1 | 1433-080 |
| 456 | Cylinder screw Ml12 x 30 | 4 | 4 | 1413-386 |
| 458 | Slay bolt | 1 | 1 | 2111-129 |
| 459 | Magnet | 4 | 4 | 1517-022 |
| 460 | Intermediate ring | 4 | 4 | 3424-039 |
| 461 | Elastomer ring | 2 | 2 | 1334-012 |
| 470 | Filter element | 1 | 1 | 1517-121 |
| 471 | Piug 1/4" | 1 | 1 | 1343-025 |
| 472 | Gasket ring dia. 21/14 x 2,0 | 1 | 1 | 1331-428 |
| 473 | O-ring dia. 20,22 x 3,53 | 1 | 1 | 1331-019 |
| 480 | Filter housing | 1 | 1 | 3042-084 |
| 481 | O-ring dia 183.74 x 3.53 (new production series) | 1 | 1 | 1331-104 |
| 432 | Cylinder screw M8 x 25 | 4 | 4 | 1413-357 |
| 483 | Pointed screw M6 x 8 | 3 | 3 | 1413-230 |
| Ftow switch arrarngement | ||||
| 500 | Terminal box | 1 | 1 | 1554-001 |
| 505 | Nippel | 1 | 1 | 2314-106 |
| 506 | Dowty ring 34,9/27,1 x 2.3 | 1 | 1 | 1331-433 |
| 507 | Flow switch with ball | 1 | 1 | 1553-024 |
| 508 | Washer | 1 | 1 | 2114-046 |
| 509 | Gasket ring 19/14 x 1,5 | 1 | 1 | 2356-124 |
| 510 | Spring | 1 | 1 | 2144-041 |
| 511 | Circlip (part of pos. 507) | 1 | 1 | |
| Compressor relief valve system | ||||
| 700-1 | Back pressure independent safety valve BSV8, 18 bar | 1 | 1 | 2416-202 |
| 700-2 | Back pressure independent safety valve BSV8, 20 bar | 1 | 1 | 2416-203 |
| 700-3 | Back pressure independent safety valve BSV8, 21bar | 1 | 2416-204 | |
| 700-4 | Back pressure independent safety valve BSV8, 22 bar | 1 | 2416-224 | |
| 700-5 | Back pressure independent safety valve BSV8, 25 bar | 1 | 2416-205 | |
| 701-1 | Connection line, POV 40, dia. 12 | 1 | 3014-014 | |
| 701-2 | Connection line, POV 50. dia. 12 | 1 | 3014-015 | |
| 702 | Cylinder screw M12 x 35 | 4 | 4 | 1413-387 |
| 703 | O-ring dia. 82,14 x 3,53 | 1 | 1 | 1331-077 |
| 704-1 | Main valve POV 40 including conneection pipe | 1 | 1 | 3014-005 |
| 704-2 | Main valve POV 50 including conneection pipe | 1 | 1 | 3014-008 |
| 715 | Cover | 1 | 1 | 3013-177 |
| 716 | Cylinder screw M16 x 40 | 4 | 4 | 1413-432 |
| 717 | O-ring dia, 132,94 x 3,53 | 1 | 1 | 1331-093 |
| 721 | Cylinder screw M12 x 30 | 4 | 4 | 1413-386 |
| 722 | O-ring dia. 63,09 x 3,53 | 1 | 1 | 1331-071 |
| 725 | Banjo coupling | 1 | 1 | 1349-091 |
| 726 | Al gasket, dia 24/13 x 1,5 | 1 | 1 | 2356-127 |
| 727 | Reduced G 3/4" -G3/8" . | 1 | 1 | 2312-038 |
| 730 | Union nut G 1" - G 3/8". | 1 | 1 | 2469-070 |
| 732 | Al gasket, dia. 30/16 x 1,5 | 1 | 1 | 2356-137 |
| Temperature/pressure transducers | ||||
| 751 | Pressure transducer, suction gas (PT1) | 1 | 1 | 1373-249 |
| 752 | Pressure transducer, oil after filter (PT3) | 1 | 1 | 1373-271 |
| 753 | Pressure transducer, oil before filter (PT4) | 1 | 1 | 1373-271 |
| 755 | Coupling 10-RL | 2 | 2 | 1349-137 |
| 755 | Elbow coupling 10-RL | 1 | 1 | 1349-233 |
| 761 | Temperature transmitter, compressor oil (TT6) | 1 | 1 | 1373-281 |
| 752 | Temperature transmitter,suction gas (TT7) | 1 | 1 | 1373-282 |
| 765 | Gasket ring DKA R 1/4 | 2 | 2 | 1349-135 |
| Spare parts survey for SAB 163 Mk3 unit | |||
| The following list comprises all components that can be fitted on a compressor unit. | |||
| From this list we have selected the components that are used on a particular unit and which are indicated on the piping diagram of this instruction manual. The position numbers on the piping diagram are a reference to the "Pos." columns of this list. | |||
| The piping diagram is dedicated to the compressor number stated on page 1of this instruction manual. | |||
| The components in the shaded areas are variable. This may be due to voltage, refrigerant, approved pressure ets. | |||
| On ordering spare parts ft may be an advantage to recerve them in sets selected tor your specific compressor unit. | |||
| A list of sets can had on request from SABROE's local representative. | |||
| Pos. | Designation | Part no. | |
| Regulating & Control device | UNISAB II | ||
| PT1 | Pressure transducer -1 - 9 bar | 1373-249 | |
| PT2 | Pressure transducer -1 -25 bar | 1373-271 | |
| PT3 | See PT2 | ||
| PT4 | See PT2 | ||
| TT5/6/7 | Temperature transducer PT100 | 1373-264 | |
| GT8 | Position transmitter (capacity) | 3448-004 | |
| GT9 | See GT8 | ||
| UNIBAB II Frontpanel | 1573-007 | ||
| 1 CPU-module | 1572-026 | ||
| 1 Ralay print | 1574-016 | ||
| 1 EPROM extractor | 1613-002 | ||
| 1 EEPROM exctractor | 1613-003 | ||
| 1 EEPROM | 1571-015.1 | ||
| 3 Jumpers | |||
| 2 Fuses | 1572-018 | ||
| 1 Screw driver | |||
| Refrigerant system | Suction: | ||
| 20 | O-ring dia 132,94 x 3,53 | 1331-093 | |
| Set of gaskets for SCV100 (R717) | 3184-079 | ||
| Set of gaskets for SCV150 (R22) | 3184-081 | ||
| 24 | |||
| 34-35 | Set of gaskets for SNV 8 | 2453-053 | |
| 47-48 | |||
| Oil separator, general: | |||
| 30 | Sealing ring dia. 42/49 x 6,5 | 1349-213 | |
| 30 | Heating rod, 250 V | 3181-038 | |
| Heating rod, 115V | 3181-039 | ||
| Heating rod, 230 | 3181-040 | ||
| 31 | O-ring dia 52,07 x 2,62 (sight glass) | 1331-140 | |
| Sight glass | 1226-017 | ||
| 55 | O-ring dia 329,57 x 5,33 (tor cover) | 1331-184 | |
| 55 | Oil separating element | 1517-061 | |
| Oil return: | |||
| 52 | Nozzle valve | 1364-151 | |
| 53 | Sight glass | 1226-014 | |
| 53 | Gasket dia. 40.5/33 x 1.5 | 2356-144 | |
| Discharge: | |||
| 204 | Set of gaskets for SCV100 | 3184-079 | |
| O-ring dia 120,4 x 3,53 | 1331-089 | ||
| 22 | Safety valves: | ||
| 28 | DM 32/50 | ||
| Gasket, dia. 75/61 x 2.0 | 2356-220 | ||
| Gasket, dia. 109/95 x 2.0 | 2356-222 | ||
| O-rirg dia. 91.67 x 3.53 (house) | 1331-060 | ||
| Conical seat for DN 32/50 | 1365-079 | ||
| Spring (for 25 Bar opening pressure) | 1365-048 | ||
| DN 50/80 | |||
| Gasket, dia, 87/73 x 2.0 | 2356-221 | ||
| Gasket, dia, 120/106 x 2.0 | 2356-223 | ||
| O-ring dia. 117.07 x 3.53 (house) | 1331-088 | ||
| Conical seal for DN 50/8O | 1365-080 | ||
| Spring (for 25 Bar opening pressure) | 1365-050 | ||
| Oil system | Flange connection, oil tube | ||
| Gasket, dia 75/61 x 2,0 | 2356-220 | ||
| O-ring dia 59.92 x 3.53 (compr.) | 1331-071 | ||
| Oil by-pass (at pump) | |||
| Gasket, dia 131/95 x 1,5 (non-return valve) | 2356-104 | ||
| O-ring dia 40,94 x 2,62 (non-return valve) | 1331-298 | ||
| Pressure build up for capacity reg. | |||
| Non-return valve 18,1 bar | 1364-009 | ||
| Non-return valve 10,02 bar | 1364-008 | ||
| Oil pump | |||
| 63 | Shaft seal complete | 1332-192 | |
| 63 | O-ring dia 44,12 x 2,62 (cover for pump) | 1331-146 | |
| 64-65 | Set of gaskets for SVA 15 | 2453-022 | |
| 60-62 | Set of gaskets for SVA 32 | ||
| 61 | Fitler element 150 | 2464-233 | |
| 61 | O-ring dia 44.04 x 3,53 | 1331-022 | |
| 61 | O-ring dia 36,09 x 3,53 | 1331-029 | |
| 61 | O-ring dia 13,94 x 2,62 | 1331-014 | |
| Capacity regulation | 46 | Thermostatic three-way valve, type RT5 | |
| O-ring, Neoprene | 1331-383 | ||
| Thermo element, 48'C | 1365-005 | ||
| 70 | Solenoid valve block | ||
| Valve housing EVM (NC) | 1372-335 | ||
| Gasket set for EVM (NC/NO) | 1336-024 | ||
| Coil 10 W 220 V 50/60Hz | 1372-537 | ||
| 110 V 50/60Hz | 1372-538 | ||
| 240 V 50Hz | 1372-539 | ||
| 71 | Solenoid valve | ||
| Valve housing EVM (NO) | 1372-425 | ||
| Gasket set for EVM | 1336-024 | ||
| Throttle valve | |||
| 72 | Gasket set 6F | 1377-210 | |
| 73 | Solenoid valve: | ||
| See pos.70 | |||
| 74 | Solenoid valve | ||
| BLI Oil cooling | 80-84 | Gatket set for SVA 15-20 | 2453-022 |
| 81 | Filter FA15: | ||
| (When TEAT 28 is selected) | |||
| Gasket set for FA15 | 1377-078 | ||
| Repair kit for FA15 | 1377-250 | ||
| Filter FA20: | |||
| 81 | (When TEAT 85 is setected) | ||
| Gasket set for FA20 | 1377-079 | ||
| Repair kit for FA20 | 1377-251 | ||
| 82 | Solenoid valve EVRA15 | ||
| (whenTEAT 20 is selected) | |||
| Gasket set (for EVRA15) | 1377-093 | ||
| Repair kit (for EVRA 15) | 1377-099 | ||
| Coil 10W 220 V 50/60 Hz | |||
| 110 V 50/60 Hz See pes 70 | |||
| 240 V 50 Hz | |||
| 82 | Solenoid valve EVRA20 | ||
| (when TEAT 85 is selected) | |||
| Gasket set (for EVRA 20) | 1377-094 | ||
| Repair kit (for EVRA 20) | 1377-069 | ||
| Coil 10W 220 V 50/60 Hz | |||
| 110 V 50/60 Hz See pes 70 | |||
| 240 V 50 Hz | |||
| 83 | Injection valve TEAT 20 | ||
| Nozzle insert 20-8 | 1371-203 | ||
| Nozzle inset 20-12 | 1371-204 | ||
| Nozzle insert 20-20 | 1371-206 | ||
| Thermal part 35-65 deg. C | 1371-255 | ||
| Thermal part 55-95 deg. C | 1371-253 | ||
| 83 | Injection valve TEAT 85 | ||
| Nozzle insert 85-33 | 1371-207 | ||
| Nozzle Insert 85-55 | 1371-208 | ||
| Nozzle insert 85-85 | 1371-209 | ||
| Thermal part 35-65 deg. C | 1371-257 | ||
| Thermal part 55-95 deg. C | 1371-250 | ||
| 83 | Injection valve PMFL 80 | ||
| Gasket set | 1377-040 | ||
| Piston rod | 1377-086 | ||
| Compr. connections | Spare parts set for coupling S952 size 262 | ||
| Sheets, bolts, nuts & slices | 1524-125 | ||
| Spacer bushing | 1526-003 | ||
| Stop screw M 10 x 10 | 1413-250 | ||
| Combination wrench 9/16" | Compr. | ||
| Box wrench 9/16" | Tools | ||
| Alignment motor - compressor | |||
| Discs (motor up to IEC 280) | 2221-067 | ||
| Discs ( motor from IEC 315) | 2221-076 | ||
| Tools | 3183-104 | ||
| Tools for compressor SAB 163 Mk3 |
| Line no. A401 = Normal set (part no. 3083-047) |
| Line no. A402 = Extendet set (part no. 3083-049 incl. 3083-048) |
| Line no. B401 = Tools for alining the coupling (part no. 3183-104) |
| Line no. B402 =Tools tor shaft seal removal, oil pump (part no.3083-160) |
| Tools no. | Designation | Part no. | A401 | A402 | B401 | B402 |
| 1 | Pullar for bearings | 3083-131 | 1 | 1 | ||
| 2 | Thrust ring for the puller, female : | 3083-130 | 1 | 1 | ||
| 3 | Thrust ring for the puller, male | 3083-054 | 1 | 1 | ||
| 4 | Tools for fitting the bearings | 3083-058 | 1 | 1 | ||
| 5 | Ring for the puller | 3083-053 | 1 | 1 | ||
| 6 | Tools for pressing out the rotors | 3083-132 | 1 | 1 | ||
| 7 | Tools for fitting the bearings | 3083-133 | 1 | 1 | ||
| 8.1 | Retaining cup formate rotor | 3083-102 | 1 | 1 | ||
| 8.2 | Retaining cup for female rotor. | 3083-103 | 1 | 1 | ||
| 9 | Tools for dismounting the bearings | 3083-052 | 2 | 2 | ||
| 10 | Thrust washer | 3083-129 | 1 | 1 | ||
| 11 | Locking tool for rotor | 3083-128 | 1 | 1 | ||
| 12 | Bearing dia 42/25 x 11 | 1512-015 | 1 | 1 | ||
| 20.1 | Threaded pins M10 x 160 | 2112-129 | 4 | 4 | ||
| 20.2 | Threaded pin M16 x 325 | 2112-151 | 1 | 1 | ||
| 21.1 | Hexagon head screw M20 x 120 | 1424-298 | 1 | 1 | ||
| 21.2 | Hexagon head screw M10 x 130 | 1424-203 | 4 | 4 | ||
| 22.2 | Socket cap screw M8 x 35 | 1413-359 | 1 | 1 | ||
| 22.3 | Socket cap screw M8 x 120 | 1413-314 | 1 | 1 | ||
| 22.4 | Socket cap screw M10 x 25 | 1413-371 | 4 | 4 | ||
| 22.6 | Socket cap screw M16 x 50 | 1413-434 | 1 | 1 | ||
| 22.7 | Hexagon head screw M16 x 130 | 1424-113 | 1 | 1 | ||
| 23.1 | Nuts M8 | 1432-063 | 2 | 2 | ||
| 23.2 | Nuts M10 | 1432-064 | 4 | 4 | ||
| 23.3 | Nuts M16 | 1432-067 | 1 | 1 | ||
| 24.2 | Washer dia. 45/17 x 5 | 3083-114 | 4 | 4 | ||
| 25 | Guide pin M16 x 300 | 2112-147 | 2 | 2 | ||
| 30 | Tools for adjusting the bearings | 3083-101 | 1 | 1 | ||
| 31 | Special screw for adjusting the bearings | 3083-100 | 1 | 1 | ||
| 32.2 | Eye bolt M16 | 1427-156 | 1 | 1 | ||
| 33 | Alignment device for coupling | 3133-104 | 1 | |||
| 34 | Feeler gauge | 1622-050 | 1 | |||
| 36 | Tools for shaft seal removal, oil pump Consists of: | |||||
| 33,1 | Puller for shaft seal, oil pump | 3083-157 | 1 | |||
| 36,2 | Cap screw M10 x 75 | 1424-201 | 1 | |||
| 36,3 | Threaded pin M8 x 150 | 3083-156 | 3 | |||
| 36,4 | Nuts M8 | 1432-063 | 3 | |||
| 36,5 | Punch dia. 18 x 80 | 3083-158 | 1 | |||
| 36,6 | Punch dia. 22/16,5 x 100 | 3083-159 | 1 | |||
| 40.1 | Torque wrench (Ratchet) 5 - 50 Nm 1/2" | 1 | ||||
| 40.2 | Torque wrench 40-200 Nm (14 x 18) | 1 | ||||
| 42 | Extention 1/2° | 1 | ||||
| 43 | Converter for torque wench(14x18) - 1/2" | 1 | ||||
| 44.2 | Hexagon bit adaptor 1/2" - 5mm | 1 | ||||
| 44.3 | Hexagon bit adaptor 1/2" - 6mm | 1 | ||||
| 44.4 | Hexagon bit adaptor 1/2" - 8mm | 1 | ||||
| 44.5 | Hexagon bit adaptor 1/2" - 10mm | 1 | ||||
| 44.6 | Hexagon bit adaptor 1/2" - 14mm | 1 | ||||
| 45 | Box spanner insert 1/2" - 19mm | 1 | ||||
| 45.2 | Box spanner insert 1/2" - 30mm | 1 | ||||
| 45,3 | Box spanner insert 1/2" - 36mm | 1 | ||||
| 45.4 | Box spanner insert 1/2"-9/16" | 1 | ||||
| 46 | Open end spanner (14 x 18) - 24mm | 1 | ||||
| 50.1 | Combination spanner 17mm | 1612-276 | 1 | |||
| 50.2 | Combination spanner 9/16" | 1 | ||||
| 51.1 | Allen key for socket cap screw 3mm | 1612-395 | 1 | |||
| 51.2 | Allen key for socket cap screw 5mm | 1612-397 | 1 | |||
| 51.3 | Allen key for socket cap screw 6mm | 1612-398 | 1 | |||
| 51.4 | Allen key for socket cap screw 8mm | 1612-399 | 1 | |||
| 51.5 | Allen key for socket cap screw 10mm | 1612-401 | 1 | |||
| 51.6 | Allen key for socket cap screw 14mm | 1612-400 | 1 | |||
| 52 | Magnetic Fixture for dial indicator | 1 | ||||
| 53 | Dial indicator | 1 | ||||
| 54.1 | Retaining ring plier | 1 | ||||
| 54.2 | Retaining ring plier | 1 | ||||
| 55.1 | Hammer | 1612-012 | 1 | |||
| 55.2 | Plastics hammer | 1612-042 | 1 | |||
| 56 | Steel punch 10 mm | 1 | ||||
| 57 | Plier for driving pin | 1612-190 | 1 |
List of parts for SAB 202
| List of parts for SAB 202 | |||
| Relevant drawing 0661-855 | |||
| Pos | Designation | No | Part no |
| Complete compressor LF, aut. Vi | 4161-059 | ||
| Complete compressor LF, man. Vi | 4161-060 | ||
| Complete compressor LM, aut. VI | 4161-061 | ||
| Complete compressor LM, man, Vi | 4161-062 | ||
| Complete compressor SF, aut. VI | 4161-063 | ||
| Complete compressor S F, man. Vi | 4161-064 | ||
| Complete compressor SM, ant, Vi | 4161-065 | ||
| Complete compressor SM, man. Vi | 4161-066 | ||
| Compressor housing | |||
| 10-1 | Compressor housing (L) | 1 | 3011-009 |
| 10-2 | Compressor housing (S) | 1 | 3011-019 |
| Bearing cover at suction end | |||
| 20-1 | Bearing cover, female drive | 1 | 3013-089 |
| 20-2 | Bearing cover, male drive | 1 | 3013-110 |
| 21 | O-ring dia. 430,66 x 3,53, neoprene | 1 | 1331-117 |
| 22 | Innar sleeve, INA IR dia. 17/20 x 16 | 2 | 1514-018 |
| 23 | Washer dia. 25/16.5 x 4 | 4 | 2114-047 |
| 24 | mreaded plug with cottar 1/2 | 1 | 1343-027 |
| 25 | Dowty ring 025 | 1 | 1331-430 |
| 26 | Cylindrical screw M16 x 60 | 10 | 1413-436 |
| 27 | Cylindrical screw M 16 x 30 | 2 | 1413-429 |
| 28 | Cylindrical screw Ml 6 x 180 | 8 | 1413-428 |
| 30 | Hose connection | 1 | 1345-143 |
| Bearing cover at ditcharge end | |||
| 40 | Thrust cover/capacity regulating cylinder | 1 | 3013-150 |
| 41 | Cylinder screw M16 x 60 | 20 | 1413-436 |
| 42 | Washer dia. 35/16,5 x 4 | 4 | 2114-047 |
| 43 | O-ring dia. 151,93 x 3,53, neoprene | 1 | 1331-099 |
| 44 | Adjusting screw | a | 2111-128 |
| 45 | Locking screw M6 x 10 | 4 | 1413-231 |
| 46 | Cross bar for bearing adjustment | 1 | 3083-137 |
| 47 | Cylinder screw M12 x 30 | 6 | 1413-366 |
| 48 | Inner sleeve, INA IR dia 17/20 x 16 | 2 | 1514-018 |
| 49 | O-ring dia. 13,94 x 2,62 | 1 | 1331-014 |
| Cover for capacity regulating cylinder | |||
| 60 | Cover for capacity cylinder | 1 | 3013-197 |
| 61 | O-ring dia. 142,47 x 3,53 - neoprene | 1 | 1331-096 |
| 62 | Cylinder screw M12 x 35 | 4 | 1413-387 |
| Housing for capacity indicator | |||
| 70 | Housing for capacity indicator | 1 | 3045-002 |
| 71 | Cylinder screw M6 x 30 | 4 | 1413-343 |
| 72 | Cover for capacity indicator | 1 | 3045-003 |
| 73 | Cylinder screw M6 x 50 | 4 | 1413-347 |
| 74 | O-ring dia. 98.02 x 3,53, neoprene | 1 | 1331-081 |
| 75-1 | Glass for indicator (L) | t | 3045-050 |
| 75-2 | Glass for indicator (S) | 1 | 3045-049 |
| Rotors | |||
| 110-1 | Set of rotors tor SM | 1 | 3024-102 |
| 110-2 | Set of rotors tor SF | 1 | 3024-097 |
| 110-3 | Set of rotors for LM | 1 | 3024-103 |
| 110-4 | Set of rotors for LF | 1 | 3024-095 |
| 111 | Journal bearing | 4 | 1515-031 |
| 112 | Retaining pin for journal bearing dia, 5 x 45 | 4 | 1446-033 |
| 113 | Cylinder screw M6 x 45 | 8 | 1413-340 |
| 114 | Thrust washes | 2 | 3021-029 |
| 115 | Cylinder screw M16 x 45 | 2 | 1413-433 |
| 132 | Four point ball bearing dia. 70/150 x 35 | 2 | 1513-040 |
| 133 | Set of shims dia. 128/150 for adjusting the clearance between the rotor and outlet port. Comprising: 1 off thickness 5,60 mm | 2 | 3021-043 |
| 1 - 5,65 mrr | |||
| 1 - 5,70 mm | |||
| 1 - 5,75 mm | |||
| 1 - 5,80 mrn | |||
| 1 - 5,85 mm | |||
| 1 - 5,90 mm | |||
| 134 | Balance piston. drive rotor | 1 | 3025-052 |
| 135 | Spacer ring, drive rotor | 1 | 3025-035 |
| 136 | Retaining ring 4 x 10 | 1 | 1446-012 |
| 137 | Balance piston, driven rotor | 1 | 3025-034 |
| 138 | Spacer ring, driven rotor | 1 | 3025-036 |
| 139 | Retaining pin 5x16 | 1 | 1446-021 |
| DIscharga ports | |||
| 140-1 | Discharge port for male rotor . | 1 | 3031-031 |
| 141-1 | Discharge port for female rotor | 1 | 3031P032 |
| 142 | Cylinder scraw M8 x 190 | 6 | 1413-309 |
| 143 | Washer for discharge port dia. 16,5 /8,2 x 10 | 6 | 2114-045 |
| 144 | Cylinder screw M6 x 30 | 2 | 1413-343 |
| 145 | Pointed screw M10 x 35 - inside adjustment | 2 | 1413-255 |
| 146 | Locking screw M10 x 10 - inside adjustment | 2 | 1413-253 |
| 147 | Locking screw M10 x 10 - outside adjustment | 2 | 1413-253 |
| 148 | Pointed screw M10 x 20 - outside adjustment | 2 | 1413-032 |
| 149A | Blank of screw 3/8" - outside adjustment | 2 | 1343-026 |
| 149B | Gasket - outside adjustment | 2 | 1331-427 |
| Parts for adjusting rotors | |||
| 153 | Inner cover | 2 | 3021-030 |
| 154 | O-ring dia. 142,47 x 3,53 | 2 | 1331-096 |
| 155 | Cylindrical steel roll 8H 11 x 8 | S | 1514-019 |
| Shaft seal | |||
| 160A | Shaft seal collar 1 | ||
| 160B | Shaft saal seat 1 | ||
| 160C | O-ring for shaft seat collar 1 | 1 | 3084-557 |
| 160D | O-rlng for shaft saal seat 1 | ||
| 160E | Pointed screw 3 | ||
| 161 | Retaining pin for shaft seal seat dia. 3 x 5 | 1 | 1446-005 |
| 162 | Spirolox ring (oil thrower) | 1 | 1437-294 |
| 163-1 | Cover, F | 1 | 3013-100 |
| 163-2 | Cover, M | 1 | 3013-102 |
| 164 | O-ring dia, 132,94 x 3,53, neoprene | 1 | 1331-093 |
| 165-1 | Cover for shaft seal, F | 1 | 3013-099 |
| 165-2 | Cover for shaft seal, M | 1 | 3013-101 |
| 166 | O-ring dia, 158,34 x 3,53 | 1 | 1331-100 |
| 167 | Cylinder screw M12 x 35 | 8 | 1413-387 |
| 168 | Hose connection branch 1 /4° | 1 | 1345-143 |
| 169 | Clear plastic hose | 1 | 1241-190 |
| Suction filter | |||
| 170 | Suction filter | 1 | 3042-075 |
| Adjusting system for Vi-slide, AUT | |||
| 352 | Screw for transmitter M3 x 8 (included in pos. 410) | (4) | 1412-012 |
| 371 | Sealing ring OD 70 | 1 | 1332-126 |
| 372 | Attachment for pin | 1 | 3044-035 |
| 380 | Cover tor aut. Vi | 1 | 3013-196 |
| 381 | O-ring dia. 101,19 x 3,53, neoprene | 1 | 1331-083 |
| 382 | Cylinder screw M12 x 35 | 4 | 1413-387 |
| 384 | Attachment for sealing ring | 1 | 3044-034 |
| 385 | Cylinder screw M4 x 16 | 2 | 1413-320 |
| 386 | Cylindrical pin dia. 6 x 16 | 2 | 1445-076 |
| 387 | Cylinder screw M6 x 12 | 1 | 1413-339 |
| 390 | Spindle aut. Vi | 1 | 3044-063 |
| 393 | Ball baaring 6202 | 1 | 1511-012 |
| 395 | Driving disk | 1 | 3044-021 |
| 396 | Cylinder screw M4 x 12 | 1 | 1413-318 |
| 400 | Attachment tor transmitter | 1 | 3044-064 |
| 401 | Cylinder screw M6 x 80 | 4 | 1413-307 |
| 402 | Cover ring for transmitter | 1 | 3045-009 |
| 403 | Cylinder screw M4 x 10 | 4 | 1413-319 |
| 405 | Magnetic coupling | 1 | 3045-062 |
| 406 | O-ring dia. 32,99 x 2,62 (incl in pos. 405) | (1) | 1331-133 |
| 407 | Hexagon head screw M4 x 16 (inc. in pos. 405) | (1) | 1413-320 |
| 410 | Turning transmitter | 1 | 3448-004 |
| 411 | Driving lug | 1 | 3044-020 |
| 412 | Pointed screw M4 x 5 | 1 | 1413-211 |
| 413 | Clamping pin dia. 1,5 x 12 | 1 | 1446-010 |
| Adjusting system for Vi-slide, MAN | |||
| 180 | Spindle man. Vi | 1 | 3044-052 |
| 181 | Cover for man. Vi | 1 | 3013-093 |
| 182 | Sealing washer for slide stop | 1 | 3044-014 |
| 183 | Sealing ring | 1 | 1331-503 |
| 184 | O-ring dia. 44,04 x 3,53, neoprene | 1 | 1331-065 |
| 185 | Retainer for bearings | 1 | 3044-033 |
| 186 | Axial ball bearing dia. 42/25 x 11 | 2 | 1512-015 |
| 187 | Locking plate | 1 | 2114-043 |
| 188 | Cylinder screw M6 x 12 | 1 | 1413-339 |
| 189 | Thread washer | 1 | 3044-073 |
| 195 | Cylinder screw M4 x 30 | 2 | 1413-325 |
| 196 | Cylinder screw M6 x 35 | 3 | 1413-344 |
| 197 | O-ring dia. 101,19 x 3,53 | 1 | 1331-083 |
| 198 | Cylinder screw M12 x 35 | 4 | 1413-387 |
| Vi-slide | |||
| 190-1 | Slide stop, S | 1 | 3043-131 |
| 190-2 | Slide stop, L | 1 | 3043-130 |
| 191-1 | Spring for Vi-slide,L | 1 | 2144-042 |
| 191-2 | Spring for Vi-slide,S | 1 | 2144-043 |
| 192 | Cylinder screw M 10 x 25 | 1 | 1413-371 |
| Capacity regulating slide | |||
| 200-1 | Slide for L | 1 | 3043-113 |
| 200-2 | Slide for S | 1 | 3043-125 |
| 201 | Piston part inner | 1 | 3043-138 |
| 202 | Piston part outer | 1 | 3043-139 |
| 203 | O-ring dia. 40,87 x 3,53, neoprene | 1 | 1331-064 |
| 204 | Sealing ring dia. 150 | 1 | 1332-133 |
| 206 | Slotted nut KM8 | 1 | 1514-200 |
| 207A-1 | Piston rod for L | 1 | 3043-140 |
| 207A-2 | Piston rod for S | 1 | 3043141 |
| 207B | Bushing tor indicator spindle Included in pos. 207A | 1 | 3045-046 |
| 207C | Cylindrical pin dia. 6 x 16 Included in pos. 207A | 1 | 1445-076 |
| 207D | Spirolox-ring Inducted in pos. 207A | 1 | 1437-291 |
| 207E | Steel ball 3/8" Included in pos. 207A | 1 | 1514-158 |
| 208 | Locking plate for slotted nut | 1 | 1514-070 |
| 209 | Tape bearing | 2 | 2132-100 |
| 311 | Cap torew M20 x 60 | 1 | 1424-289 |
| 313 | Clamp | 1 | 3042-054 |
| Spindle for copacity indication | |||
| 210 | Spindle tor capacity indication | 1 | 3045-059 |
| 216 | Magnetic coupling | 1 | 3045-061 |
| 217 | O-ring dia. 44,12 x 2,62 (incl. in pos. 216) | (1) | 1331-146 |
| 218 | Hexagon head screw M4 x 16 (Incl. in pos. 216) | (1) | 1413-320 |
| 219 | Hexagon head screw M4 x 20 (ind. in pos. 216) | (2) | 1413-322 |
| Capacity indication | |||
| 221 | Indication disk | 1 | 3045-001 |
| 223 | Socket cap screw M4 x 10 | 1 | 1413-319 |
| 224 | Backing ring 105/90 x 1,6 | 1 | 2356-155 |
| 226 | Locking washer DC 15/8,4 | 1 | 1437-054 |
| 227 | Locking washar DC 8/4,3 | 1 | 1437-060 |
| 350 | Position transmitter | 1 | 3448-004 |
| 351-1 | Indicator glass, L (replacing pos. 75-1 when transmitter) | 1 | 3045-048 |
| 351-2 | Indicator glass, S (replacing pos. 75-2 whentransmitter) | 1 | 3045-047 |
| 352 | Screw for transmitter M3 x 8 (incl. in pos. 350) | (4) | 1412-012 |
| Non return valve | |||
| Non return valve complet | 3042-172 | ||
| 252 | O-ring dia. 253,37 x 5,33, neoprene | 1 | 1331-181 |
| 253 | Intermediate flange | 1 | 3013-288 |
| 255 | Valve housing | 1 | 3042-127 |
| 256 | Spindle guide | 1 | 3042-125 |
| 257 | Retainer | 1 | 3042-126 |
| 258 | Hexagon head screw M8 x 120 | 3 | 1413-314 |
| 259 | Valve cone | 1 | 3042-123 |
| 260 | Spindle | 1 | 3042-124 |
| 261 | Spring | 1 | 1523-033 |
| 262 | Tape bearing dim 10 x 1 x 46 | 1 | 2132-114 |
| 263 | Tape bearing dim 10 x 1 x 105 | t | 2132-096 |
| 264 | Hexagon head screw M16 x 75 | 8 | 1424-108 |
| 265 | Countersunk socket cop. screw M12 x 25 | 1 | 1413-115 |
| 266 | Hexagon bead scraw M12 x 30 | 2 | 1413-386 |
| 267 | Shaft nut KM9 - M45 | 1 | 1514-201 |
| 268 | Seeger ring dia. 14 x 1,0, DIN 471 | 1 | 1437-207 |
| Oil injection | |||
| 316 | V-joint 22-RL | 1 | 1349-153 |
| 317 | Check valve RVS | 1 | 1364-163 |
| 318 | O-ring dia. 33,05 x 1,78 | 1 | 1331-123 |
| 319 | Valve seat | 1 | 3042-077 |
| External oil piping | |||
| 320-1 | Pipe sat (L) | 1 | 3049-026 |
| 320-2 | Pipe set (S) | 1 | 3049-029 |
| 321 | Pipe clamp dia. 3 x 12 | 1 | 2532-012 |
| Oil filter | |||
| 450 | Oil filter cover | i | 3041-008 |
| 452 | O-ring dia. 132,94 x 3,53, neoprene | 1 | 1331-093 |
| 453 | O-ring dia. 101,19 x 3,53, neoprene | 1 | 1331-083 |
| 455 | Lock nut M10 | 1 | 1433-030 |
| 456 | Cylinder screw M12 x 35 | 4 | 1413-387 |
| 458 | Stay bolt for magnet | 1 | 2111-127 |
| 459 | Magnets for oil filter | 4 | 1517-022 |
| 460 | Intermediate ring | 4 | 3424-039 |
| 461 | Rubber ring | 2 | 1334-012 |
| 462 | Plug 1/4" | 2 | 1343-025 |
| 463 | Dowty ring dia. 20,57 x 13,74 | 2 | 1331-428 |
| 470 | Oil filter cartridge | 1 | 1517-015 |
| 475 | O-ring dia. 63,9 x 3,53 | 1 | 1331-071 |
| 476 | Cylinder screw M 12 x 30 | 4 | 1413-386 |
| Oil flow swich | |||
| 500 | Terminal box | 1 | 1554-001 |
| 501 | Cover for flow switch | 1 | 3041-004 |
| 502 | O-ring dia. 132,94 x 3,53, nroprere | 1 | 1331-093 |
| 505 | Nipple tor ftow switch o | 1 | 2314-106 |
| 506 | Dowty ring | 1 | 1331-433 |
| 507 | Flow switch with ball | 1 | 1553-024 |
| 508 | Washer | 1 | 2114-046 |
| 509 | Gasket dia. 19/14 x 1,5 | 1 | 2356-124 |
| 510 | Spring | 1 | 2144-041 |
| 511 | Circlip (included in pos. 507) | 1 | |
| 512 | Cylinder screw M12 x 35 | 4 | 1413-387 |
| Plugging | |||
| 520 | Plug 1/2" | 1 | 1343-027 |
| 521 | Dowty ring 025 | 1 | 1331-430 |
| 525 | Plug 3/4" | 1 | 1343-028 |
| 526 | Dowty ring 027 | 1 | 1331-433 |
| 530 | Plug 1/4" | 1 | 1343-025 |
| 531 | Gasket ring 19/14 x 1,5 | 1 | 2356-124 |
| Economizer inlet | |||
| 600 | Eco-plug | 1 | 3013-111 |
| 601 | Cylinder screw M12 x 30 | 4 | 1413-386 |
| 602 | Cylinder screw M8 x 30 | 2 | 1413-358 |
| 603 | O-ring dia. 53,57 x 3,53, neoprene | 1 | 1331-058 |
| Relief valve | |||
| 700-1 | Back pressure independent valve. BSV 8-18 bar | 1 | 2416-202 |
| 700-2 | Back pressure independent valve. BSV 8-22 bar | 1 | 2416-224 |
| Pilot operated valve | |||
| 701-A | Connection line for POV 50 | 1 | 3049-032 |
| 701-B | Connection line for POV 60 | 1 | 3049-033 |
| 702-A | Cylinder screw M12 x 25 | 4 | 1413-385 |
| 702-B | Cylinder screw M 12 x 30 | 4 | 1413-388 |
| 703-A | O-ring dia. 63,09 x 3,53 | 1 | 1331-071 |
| 703-B | O-ring dia. 88,49 x 3,53 | 1 | 1331-079 |
| 704-A | Pilot operated valve, POV 50 (for R717) | 1 | 2417-046 |
| 704-B | Pilot operated valve, POV 80 (for R22 and HCF,s) | 1 | 2417-058 |
| Cover for main valve | |||
| 705-A | Cover for POV 50 | 1 | 3013-125 |
| 705-B | Cover for POV 80 | 1 | 3013-163 |
| 706 | Cylinder screw M16 x 40 | 8 | 1413-432 |
| 707 | O-rlng dia. 253.37 x 5,33 | 1 | 1331-181 |
| Connection between compr. discharge side and suction side | |||
| 710-A | Manifold for POV 50 | 1 | 3013-124 |
| 710-B | Man (fold tor POV 80 | 1 | 3013-157 |
| 711-A | O-ring dia. 85,32 x 3,53 | 1 | 1331-078 |
| 711-B | O-ring dia. 86,49 x 3,53 | 1 | 1331-079 |
| 712-A | Cylinder screw M12 x 110 | 3 | 1413-406 |
| 712-B | Cylinder screw M12 x 30 | 4 | 1413-386 |
| 715-A | Cover (for POV 50 only) | 1 | 3013-125 |
| 716 | Cylinder screw M16 x 40 | 4 | 1413-432 |
| 717 | O-ring dia. 164,69 x 3,53 | 1 | 1331-101 |
| 720-A | Pipe conneclion for POV 50 | 1 | 3014-002 |
| 720-B | Pipe connection for POV 80 | 1 | 3013-166 |
| 721-A | Cylindar screw M12 x 30 | 8 | 1413-386 |
| 721-B | Cylinder screw M12 x 40 | 4 | 1413-388 |
| 722-A | O-ring dia. 75,79 x 3,53 | 2 | 1331-075 |
| 722-B | O-ring dia. 88.49 x 3,53 | 1 | 1331-079 |
| Releif valve connections | |||
| 725 | Stud coupling A-12 RL | 1 | 1349-053 |
| 726 | Al-gasket dia.24/13 x 1,5 | 1 | 2356-127 |
| 727 | Reducer G3/4 - G3/8 | 1 | 2312-038 |
| 729 | Elbow coupling VB 12-RL | 1 | 1349-210 |
| 730 | Union nut G1 | 1 | 2313-017 |
| 731 | Threaded nipple G3/8 | 1 | 2311-065 |
| 732 | Al-gastet dia.30/16 x 1,5 | 1 | 2356-137 |
| 733 | Dowty ring 023 | 1 | 1331-427 |
| Signal trantducers | |||
| 751 | Pressure transducer, PT1 | 1 | 1373-249 |
| 752 | Pressure transducer, PT3 | 1 | 1373-271 |
| 753 | Pressure transducer, PT4 | 1 | 1373-271 |
| 755 | Stud coupling | 2 | 1349-137 |
| 756 | Stud elbow | 1 | 1349-233 |
| 761 | Temperature transmitter, TT6 | 1 | 1373-264 |
| 762 | Temperature transmitter, TT7 | 1 | 1373-264 |
| 765 | Gasket ring | 2 | 1349-135 |
| 766 | Reducer G1/2-G1/4 | 1 | 1349-077 |
| S=L/D 1.7 M=Male drive |
| L=L/D 2,2 F=Female drive |
